What to know before a replacement block drive in Beverley
Homes in Beverley include plenty of semis and detached houses with room for a drive, plus older terraces where parking is tighter.
Sloping drives are common in parts of Yorkshire, which affects falls, steps and drainage at the bottom of the drive.
How much does a replacement block drive cost in Beverley?
In Yorkshire and the Humber, a replacement block drive usually costs £85–£160 per m² including VAT. For a 45 m² replacement drive, that is roughly £3,850–£7,300. Your exact price depends on what the survey or your photos show, and is fixed in writing before anything is booked.
| Item | Guide price inc VAT |
|---|---|
| Replace tarmac or concrete with block (incl. break-out) | £85–£160 per m² |
| Breaking out an old surface | £9–£35 per m² |
| Edging or kerb, bedded and haunched | £18–£45 per metre |
| Typical channel drain run | £320–£900 |
| Dropped kerb (vehicle crossover) construction | £900–£2,700 |
Guide figures for Yorkshire and the Humber, checked 9 November 2026. See all prices or use the guide price tool.
What is included?
Replacing an old drive with block paving means breaking out the existing tarmac, concrete or gravel, checking what is underneath, and then building a block drive on a sound base. Many older tarmac and concrete drives have cracked, sunk or broken up, which is why this is such a common way into block paving.
- Levels set below the damp-proof course with falls away from the house
- New edging, sub-base where needed, and the block drive
- Drainage added where the old drive sent water to the house or road
- Assessment of the old base: keep, top up or replace
- Break-out of the old surface with waste removal and skip or grab lorry
What we check on a Beverley survey
- Existing manhole and inspection covers, and whether to recess them
- Ground conditions under the old surface and how deep the sub-base must be
- Where rain will go: falls, lawn, border, channel or soakaway
- Where an electric vehicle charger cable might run
- Steps, thresholds and door heights
Planning and kerb rules in Beverley
Beverley is in England, so these rules apply:
In England, paving in front of the house that covers more than 5 m² needs planning permission unless it is permeable or drains to a lawn, border or soakaway inside your boundary. Permeable block paving, or standard blocks laid to fall onto a planted strip, avoid the need for permission in most cases.
Flats and maisonettes, listed buildings, and homes covered by an Article 4 direction can have tighter rules, and conservation areas, National Parks and National Landscapes restrict some permitted development.
A dropped kerb needs your local highway authority's approval (usually the county, unitary, metropolitan or London borough council), and a new access onto an A, B or C classified road also needs planning permission.
General guidance, not legal advice. Your survey confirms what applies to your home. See the planning guide.
What happens next
Quick details
Your postcode and the job. It takes a minute.
On-site check
Measurements, levels against the damp-proof course, ground and drainage.
Itemised quote
Fixed once the specification is agreed, with no vague extras.
Laid and finished
Compacted, jointed and handed back clean.
Why choose Block Paving Contractors
Honest timescales
We tell you how long the job takes and what can delay it, such as approvals and weather.
Itemised quotes
Break-out, waste, edging, drainage and covers are separate lines you can see.
Clean finish
The site is swept, the joints are filled and you are shown how to look after the paving.
Edges set in concrete
Every edge restraint is bedded and haunched, so the paving cannot creep.
Replace an old drive in Beverley: questions
Do you cover Hull, Brough and Driffield?
Yes. We cover Beverley and the places around it, including Hull, Brough and Driffield, and the rest of the East Riding of Yorkshire.
How long does a replacement block drive take to build?
Most homes take between three and seven working days, depending on size, the dig and the drainage. Your quote gives the expected duration.
How much does a replacement block drive cost in Beverley?
Our guide for Beverley is £85–£160 per m² including VAT, so a 45 m² replacement drive is usually about £3,850–£7,300. Your fixed price follows the survey.
Do I need planning permission for a replacement block drive in Beverley?
In England, a front drive over 5 m² needs planning permission unless it is permeable or drains to a lawn or border within your boundary. Ask us on the survey if you are unsure.
Replace an old drive near Beverley
Nearby towns we cover for replace an old drive, and replace an old drive across East Riding of Yorkshire:
- Replace an old drive in Hull
- Replace an old drive in Brough
- Replace an old drive in Driffield
- Replace an old drive in Bridlington
- Replace an old drive in Goole
