Block paving driveways in Stanley: the local picture
In Stanley, many front gardens have already been paved once, so new paving often starts with breaking out the old surface.
Wind-driven rain on the North East coast makes falls and a well-filled joint more important.
How much does a block paved driveway cost in Stanley?
In the North East, a block paved driveway usually costs £75–£125 per m² including VAT. For a 50 m² double drive, that is roughly £3,850–£6,300. Your exact price depends on what the survey or your photos show, and is fixed in writing before anything is booked.
| Item | Guide price inc VAT |
|---|---|
| Concrete block driveway, new sub-base | £75–£125 per m² |
| Breaking out an old surface | £9–£35 per m² |
| Edging or kerb, bedded and haunched | £18–£45 per metre |
| Typical channel drain run | £320–£900 |
| Dropped kerb (vehicle crossover) construction | £900–£2,700 |
Guide figures for the North East, checked 9 November 2026. See all prices or use the guide price tool.
What does a block paved driveway involve?
A block paved driveway is a surface of small concrete or clay blocks laid tightly on a bed of sharp sand, held in by a fixed edge and locked together with kiln-dried jointing sand. Laid on a properly dug and compacted sub-base, it carries cars for decades, and a single damaged block can be lifted and replaced without breaking the surface.
- Cuts at edges, around covers and against the house
- Crushed-stone sub-base laid in layers and compacted
- Blocks laid in your chosen pattern, with a contrasting border if wanted
- Removal of the old surface and soil to the agreed depth, with waste taken away
- Edge restraints or kerbs bedded and haunched in concrete
What we check on a Stanley survey
- Levels against the damp-proof course (the finished paving must sit at least 150 mm below it)
- Access for a mini-digger, skip or grab lorry
- Existing manhole and inspection covers, and whether to recess them
- Where an electric vehicle charger cable might run
- Whether front-garden planning rules apply
Do you need permission in Stanley?
Stanley is in England, so these rules apply:
In England, paving in front of the house that covers more than 5 m² needs planning permission unless it is permeable or drains to a lawn, border or soakaway inside your boundary. Permeable block paving, or standard blocks laid to fall onto a planted strip, avoid the need for permission in most cases.
Flats and maisonettes, listed buildings, and homes covered by an Article 4 direction can have tighter rules, and conservation areas, National Parks and National Landscapes restrict some permitted development.
A dropped kerb needs your local highway authority's approval (usually the county, unitary, metropolitan or London borough council), and a new access onto an A, B or C classified road also needs planning permission.
General guidance, not legal advice. Your survey confirms what applies to your home. See the planning guide.
What happens next
Quick details
Your postcode and the job. It takes a minute.
On-site check
Measurements, levels against the damp-proof course, ground and drainage.
Itemised quote
Fixed once the specification is agreed, with no vague extras.
Laid and finished
Compacted, jointed and handed back clean.
How we work
The dig and sub-base in writing
Your quote states the depth of dig, the sub-base thickness and how it is compacted.
Repair before replace
If your drive can be fixed or re-laid, we will say so.
Edges set in concrete
Every edge restraint is bedded and haunched, so the paving cannot creep.
One point of contact
You deal with one team from survey to sign-off, with work carried out by paving teams working under S&K.
Block paved driveways in Stanley: questions
Do I need planning permission for a block paved driveway in Stanley?
In England, a front drive over 5 m² needs planning permission unless it is permeable or drains to a lawn or border within your boundary. Ask us on the survey if you are unsure.
Do you cover Chester-le-Street, Consett and Durham?
Yes. We cover Stanley and the places around it, including Chester-le-Street, Consett and Durham, and the rest of County Durham.
How long does a block paved driveway take to build?
Most homes take between three and seven working days, depending on size, the dig and the drainage. Your quote gives the expected duration.
What happens to my old drive?
It is broken out and taken away by skip or grab lorry, listed as its own line on your quote.
Block paved driveways near Stanley
Nearby towns we cover for block paved driveways, and block paved driveways across County Durham:
- Block paved driveways in Chester-le-Street
- Block paved driveways in Consett
- Block paved driveways in Durham
- Block paved driveways in Seaham
- Block paved driveways in Bishop Auckland
- Block paved driveways in Peterlee
