What to know before a replacement block drive in Kilsyth
Around Kilsyth, plots are often larger and drives longer, so edging, falls and the route the water takes need planning.
Frost and heavy rain test paving in Scotland, so a well-drained sub-base and full joints matter as much as the blocks.
In Scotland block paving is often called monoblock; it is the same thing, and the same rules for the base, edging and drainage apply.
How much does a replacement block drive cost in Kilsyth?
Expect replacement block drives in Kilsyth to come in at around £95–£180 per m², including VAT at 20%. As an example, a 45 m² replacement drive usually comes to between £4,300 and £8,100.
| Item | Guide price inc VAT |
|---|---|
| Replace tarmac or concrete with block (incl. break-out) | £95–£180 per m² |
| Breaking out an old surface | £10–£40 per m² |
| Edging or kerb, bedded and haunched | £20–£50 per metre |
| Typical channel drain run | £350–£1,000 |
| Dropped kerb (vehicle crossover) construction | £1,000–£3,000 |
Guide figures for Scotland, checked 9 November 2026. See all prices or use the guide price tool.
What is included?
Sometimes the old base can be kept: a thick, sound concrete or well-compacted hardcore layer may only need trimming and topping up. Often it cannot, because it was too thin, has sunk or sits too high against the house. The survey checks levels against the damp-proof course and the existing base before the quote is written, so the price reflects the real dig.
- Break-out of the old surface with waste removal and skip or grab lorry
- New edging, sub-base where needed, and the block drive
- Drainage added where the old drive sent water to the house or road
- Assessment of the old base: keep, top up or replace
- Levels set below the damp-proof course with falls away from the house
What we check on a Kilsyth survey
- Ground conditions under the old surface and how deep the sub-base must be
- Where an electric vehicle charger cable might run
- Trees and roots near the drive
- The kerb: is it already dropped, and is it wide enough?
- Where rain will go: falls, lawn, border, channel or soakaway
Do you need permission in Kilsyth?
Kilsyth is in Scotland, so these rules apply:
In Scotland, a hard surface between the house and the road is permitted development only if it is porous or drains to a permeable area within the property. There is no 5 m² threshold: the rule applies whatever the size.
Hard surfaces are not permitted development in a conservation area or within the grounds of a listed building, so planning permission is needed there.
A dropped kerb needs consent from your council as roads authority under section 56 of the Roads (Scotland) Act 1984, and planning permission may also be needed depending on the road.
General guidance, not legal advice. Your survey confirms what applies to your home. See the planning guide.
How it works
Send the basics
Postcode, what you need and a rough size. Photos help.
Survey
We measure, check levels, ground and drainage, and talk through blocks and patterns.
Written quote
An itemised quote with the specification, the price and the start date.
The work
Our paving team builds it to the agreed specification and leaves the site swept.
What you can expect from us
Water planned first
Falls, channels and soakaways are designed before the pattern is chosen.
Itemised quotes
Break-out, waste, edging, drainage and covers are separate lines you can see.
Clean finish
The site is swept, the joints are filled and you are shown how to look after the paving.
Repair before replace
If your drive can be fixed or re-laid, we will say so.
Replace an old drive in Kilsyth: questions
Is the survey in Kilsyth free?
Yes, for new paving here: the survey and written quote are free with no obligation. Repairs and cleaning are usually priced from photos, or from a short visit where needed.
How much does a replacement block drive cost in Kilsyth?
Our guide for Kilsyth is £95–£180 per m² including VAT, so a 45 m² replacement drive is usually about £4,300–£8,100. Your fixed price follows the survey.
Do I need planning permission for a replacement block drive in Kilsyth?
In Scotland, front paving must be porous or drain within your boundary at any size, and permitted development does not apply in conservation areas. Ask us on the survey if you are unsure.
Do you cover Cumbernauld, Coatbridge and Airdrie?
Yes. We cover Kilsyth and the places around it, including Cumbernauld, Coatbridge and Airdrie, and the rest of Lanarkshire.
Replace an old drive near Kilsyth
Nearby towns we cover for replace an old drive, and replace an old drive across Lanarkshire:
- Replace an old drive in Cumbernauld
- Replace an old drive in Coatbridge
- Replace an old drive in Airdrie
- Replace an old drive in Bellshill
- Replace an old drive in Cambuslang
- Replace an old drive in Blantyre
