What to know before a replacement block drive in Clydebank
Homes in Clydebank include plenty of semis and detached houses with room for a drive, plus older terraces where parking is tighter.
In Scotland, front paving must be porous or drain within the property whatever its size, so drainage is part of every design.
In Scotland block paving is often called monoblock; it is the same thing, and the same rules for the base, edging and drainage apply.
How much does a replacement block drive cost in Clydebank?
In Scotland, a replacement block drive usually costs £95–£180 per m² including VAT. For a 45 m² replacement drive, that is roughly £4,300–£8,100. Your exact price depends on what the survey or your photos show, and is fixed in writing before anything is booked.
| Item | Guide price inc VAT |
|---|---|
| Replace tarmac or concrete with block (incl. break-out) | £95–£180 per m² |
| Breaking out an old surface | £10–£40 per m² |
| Edging or kerb, bedded and haunched | £20–£50 per metre |
| Typical channel drain run | £350–£1,000 |
| Dropped kerb (vehicle crossover) construction | £1,000–£3,000 |
Guide figures for Scotland, checked 9 November 2026. See all prices or use the guide price tool.
What is included?
Sometimes the old base can be kept: a thick, sound concrete or well-compacted hardcore layer may only need trimming and topping up. Often it cannot, because it was too thin, has sunk or sits too high against the house. The survey checks levels against the damp-proof course and the existing base before the quote is written, so the price reflects the real dig.
- Assessment of the old base: keep, top up or replace
- Drainage added where the old drive sent water to the house or road
- Break-out of the old surface with waste removal and skip or grab lorry
- New edging, sub-base where needed, and the block drive
- Levels set below the damp-proof course with falls away from the house
What we check on a Clydebank survey
- Edges against lawns, beds, walls and neighbours
- Where an electric vehicle charger cable might run
- Block range, thickness, colour and pattern to suit the house
- The kerb: is it already dropped, and is it wide enough?
- Steps, thresholds and door heights
Do you need permission in Clydebank?
Clydebank is in Scotland, so these rules apply:
In Scotland, a hard surface between the house and the road is permitted development only if it is porous or drains to a permeable area within the property. There is no 5 m² threshold: the rule applies whatever the size.
Hard surfaces are not permitted development in a conservation area or within the grounds of a listed building, so planning permission is needed there.
A dropped kerb needs consent from your council as roads authority under section 56 of the Roads (Scotland) Act 1984, and planning permission may also be needed depending on the road.
General guidance, not legal advice. Your survey confirms what applies to your home. See the planning guide.
From enquiry to finished paving
Quick details
Your postcode and the job. It takes a minute.
On-site check
Measurements, levels against the damp-proof course, ground and drainage.
Itemised quote
Fixed once the specification is agreed, with no vague extras.
Laid and finished
Compacted, jointed and handed back clean.
Why choose Block Paving Contractors
The dig and sub-base in writing
Your quote states the depth of dig, the sub-base thickness and how it is compacted.
Clean finish
The site is swept, the joints are filled and you are shown how to look after the paving.
Edges set in concrete
Every edge restraint is bedded and haunched, so the paving cannot creep.
Repair before replace
If your drive can be fixed or re-laid, we will say so.
Replace an old drive in Clydebank: questions
Do I need planning permission for a replacement block drive in Clydebank?
In Scotland, front paving must be porous or drain within your boundary at any size, and permitted development does not apply in conservation areas. Ask us on the survey if you are unsure.
What happens to my old drive?
It is broken out and taken away by skip or grab lorry, listed as its own line on your quote.
How long does a replacement block drive take to build?
Most homes take between three and seven working days, depending on size, the dig and the drainage. Your quote gives the expected duration.
Do you cover Bearsden, Milngavie and Dumbarton?
Yes. We cover Clydebank and the places around it, including Bearsden, Milngavie and Dumbarton, and the rest of Glasgow and Dunbartonshire.
Replace an old drive near Clydebank
Nearby towns we cover for replace an old drive, and replace an old drive across Glasgow and Dunbartonshire:
- Replace an old drive in Bearsden
- Replace an old drive in Milngavie
- Replace an old drive in Dumbarton
- Replace an old drive in Bishopbriggs
- Replace an old drive in Vale of Leven
- Replace an old drive in Rutherglen
