Replacing tarmac or concrete with block paving in Rosyth: the local picture
Around Rosyth, plots are often larger and drives longer, so edging, falls and the route the water takes need planning.
In Scotland, front paving must be porous or drain within the property whatever its size, so drainage is part of every design.
In Scotland block paving is often called monoblock; it is the same thing, and the same rules for the base, edging and drainage apply.
How much does a replacement block drive cost in Rosyth?
Most replacement block drive quotes in Scotland fall within £95–£180 per m² including VAT. A 45 m² replacement drive would usually be about £4,300–£8,100, with any extras listed separately on your quote.
| Item | Guide price inc VAT |
|---|---|
| Replace tarmac or concrete with block (incl. break-out) | £95–£180 per m² |
| Breaking out an old surface | £10–£40 per m² |
| Edging or kerb, bedded and haunched | £20–£50 per metre |
| Typical channel drain run | £350–£1,000 |
| Dropped kerb (vehicle crossover) construction | £1,000–£3,000 |
Guide figures for Scotland, checked 9 November 2026. See all prices or use the guide price tool.
What you get with our replace an old drive service
Replacing an old drive with block paving means breaking out the existing tarmac, concrete or gravel, checking what is underneath, and then building a block drive on a sound base. Many older tarmac and concrete drives have cracked, sunk or broken up, which is why this is such a common way into block paving.
- New edging, sub-base where needed, and the block drive
- Assessment of the old base: keep, top up or replace
- Break-out of the old surface with waste removal and skip or grab lorry
- Levels set below the damp-proof course with falls away from the house
- Drainage added where the old drive sent water to the house or road
What the survey covers
- Where an electric vehicle charger cable might run
- Edges against lawns, beds, walls and neighbours
- Access for a mini-digger, skip or grab lorry
- Trees and roots near the drive
- Existing manhole and inspection covers, and whether to recess them
Planning and kerb rules in Rosyth
Rosyth is in Scotland, so these rules apply:
In Scotland, a hard surface between the house and the road is permitted development only if it is porous or drains to a permeable area within the property. There is no 5 m² threshold: the rule applies whatever the size.
Hard surfaces are not permitted development in a conservation area or within the grounds of a listed building, so planning permission is needed there.
A dropped kerb needs consent from your council as roads authority under section 56 of the Roads (Scotland) Act 1984, and planning permission may also be needed depending on the road.
General guidance, not legal advice. Your survey confirms what applies to your home. See the planning guide.
How it works
Quick details
Your postcode and the job. It takes a minute.
On-site check
Measurements, levels against the damp-proof course, ground and drainage.
Itemised quote
Fixed once the specification is agreed, with no vague extras.
Laid and finished
Compacted, jointed and handed back clean.
What you can expect from us
Edges set in concrete
Every edge restraint is bedded and haunched, so the paving cannot creep.
Water planned first
Falls, channels and soakaways are designed before the pattern is chosen.
Clean finish
The site is swept, the joints are filled and you are shown how to look after the paving.
Itemised quotes
Break-out, waste, edging, drainage and covers are separate lines you can see.
Replace an old drive in Rosyth: questions
Do you cover Dunfermline, Dalgety Bay and Cowdenbeath?
Yes. We cover Rosyth and the places around it, including Dunfermline, Dalgety Bay and Cowdenbeath, and the rest of Fife.
How much does a replacement block drive cost in Rosyth?
Our guide for Rosyth is £95–£180 per m² including VAT, so a 45 m² replacement drive is usually about £4,300–£8,100. Your fixed price follows the survey.
Do I need planning permission for a replacement block drive in Rosyth?
In Scotland, front paving must be porous or drain within your boundary at any size, and permitted development does not apply in conservation areas. Ask us on the survey if you are unsure.
How long does a replacement block drive take to build?
Most homes take between three and seven working days, depending on size, the dig and the drainage. Your quote gives the expected duration.
Replace an old drive near Rosyth
Nearby towns we cover for replace an old drive, and replace an old drive across Fife:
- Replace an old drive in Dunfermline
- Replace an old drive in Dalgety Bay
- Replace an old drive in Cowdenbeath
- Replace an old drive in Kirkcaldy
- Replace an old drive in Glenrothes
- Replace an old drive in Methil
