Planning a replacement block drive in Wallsend
In Wallsend, many front gardens have already been paved once, so new paving often starts with breaking out the old surface.
Wind-driven rain on the North East coast makes falls and a well-filled joint more important.
How much does a replacement block drive cost in Wallsend?
For Wallsend, our guide is £85–£160 per m² including VAT, so a 45 m² replacement drive is likely to be £3,850–£7,300. Smaller jobs cost more per square metre because set-up and waste costs do not shrink with the area.
| Item | Guide price inc VAT |
|---|---|
| Replace tarmac or concrete with block (incl. break-out) | £85–£160 per m² |
| Breaking out an old surface | £9–£35 per m² |
| Edging or kerb, bedded and haunched | £18–£45 per metre |
| Typical channel drain run | £320–£900 |
| Dropped kerb (vehicle crossover) construction | £900–£2,700 |
Guide figures for the North East, checked 9 November 2026. See all prices or use the guide price tool.
What does a replacement block drive involve?
Replacing an old drive with block paving means breaking out the existing tarmac, concrete or gravel, checking what is underneath, and then building a block drive on a sound base. Many older tarmac and concrete drives have cracked, sunk or broken up, which is why this is such a common way into block paving.
- Levels set below the damp-proof course with falls away from the house
- New edging, sub-base where needed, and the block drive
- Drainage added where the old drive sent water to the house or road
- Assessment of the old base: keep, top up or replace
- Break-out of the old surface with waste removal and skip or grab lorry
What we check on a Wallsend survey
- Where rain will go: falls, lawn, border, channel or soakaway
- Edges against lawns, beds, walls and neighbours
- Ground conditions under the old surface and how deep the sub-base must be
- Steps, thresholds and door heights
- Trees and roots near the drive
Rules for front drives in Wallsend
Wallsend is in England, so these rules apply:
In England, paving in front of the house that covers more than 5 m² needs planning permission unless it is permeable or drains to a lawn, border or soakaway inside your boundary. Permeable block paving, or standard blocks laid to fall onto a planted strip, avoid the need for permission in most cases.
Flats and maisonettes, listed buildings, and homes covered by an Article 4 direction can have tighter rules, and conservation areas, National Parks and National Landscapes restrict some permitted development.
A dropped kerb needs your local highway authority's approval (usually the county, unitary, metropolitan or London borough council), and a new access onto an A, B or C classified road also needs planning permission.
General guidance, not legal advice. Your survey confirms what applies to your home. See the planning guide.
From enquiry to finished paving
Send the basics
Postcode, what you need and a rough size. Photos help.
Survey
We measure, check levels, ground and drainage, and talk through blocks and patterns.
Written quote
An itemised quote with the specification, the price and the start date.
The work
Our paving team builds it to the agreed specification and leaves the site swept.
Why choose Block Paving Contractors
Honest timescales
We tell you how long the job takes and what can delay it, such as approvals and weather.
Itemised quotes
Break-out, waste, edging, drainage and covers are separate lines you can see.
Clean finish
The site is swept, the joints are filled and you are shown how to look after the paving.
Water planned first
Falls, channels and soakaways are designed before the pattern is chosen.
Replace an old drive in Wallsend: questions
Do I need planning permission for a replacement block drive in Wallsend?
In England, a front drive over 5 m² needs planning permission unless it is permeable or drains to a lawn or border within your boundary. Ask us on the survey if you are unsure.
Is the survey in Wallsend free?
Yes, for new paving here: the survey and written quote are free with no obligation. Repairs and cleaning are usually priced from photos, or from a short visit where needed.
Can you match the blocks to my house in Wallsend?
We bring samples to the survey and suggest blocks and borders that suit the age and brick of the house. Final colour is your choice.
How long does a replacement block drive take to build?
Most homes take between three and seven working days, depending on size, the dig and the drainage. Your quote gives the expected duration.
Replace an old drive near Wallsend
Nearby towns we cover for replace an old drive, and replace an old drive across Tyne and Wear:
- Replace an old drive in Hebburn
- Replace an old drive in Jarrow
- Replace an old drive in Felling
- Replace an old drive in Gosforth
- Replace an old drive in Newcastle upon Tyne
- Replace an old drive in South Shields
