England · Replace an old drive

Replacing tarmac or concrete with block paving in Buckinghamshire

From HP5, HP6, HP7, HP8 to the villages around Buckinghamshire, we quote replacement block drives built to one written specification, so you know exactly what is going under the blocks.

  • 8 towns listed
  • £105–£195 per m² inc VAT
  • Free survey for new paving
Driveway half old cracked tarmac and half new brindle herringbone block paving

How much does a replacement block drive cost in Buckinghamshire?

Guide price in Buckinghamshire£105–£195 per m²Including VAT at 20%

In the South East, a replacement block drive usually costs £105–£195 per m² including VAT. For a 45 m² replacement drive, that is roughly £4,600–£8,750. Your exact price depends on what the survey or your photos show, and is fixed in writing before anything is booked.

ItemGuide price inc VAT
Replace tarmac or concrete with block (incl. break-out)£105–£195 per m²
Breaking out an old surface£11–£45 per m²
Edging or kerb, bedded and haunched£20–£55 per metre
Typical channel drain run£380–£1,100
Dropped kerb (vehicle crossover) construction£1,100–£3,250

Guide figures for the South East, checked 9 November 2026.

Towns we cover in Buckinghamshire

Choose a town for local prices and details for replace an old drive:

What does a replacement block drive involve?

Sometimes the old base can be kept: a thick, sound concrete or well-compacted hardcore layer may only need trimming and topping up. Often it cannot, because it was too thin, has sunk or sits too high against the house. The survey checks levels against the damp-proof course and the existing base before the quote is written, so the price reflects the real dig.

Planning-sensitive towns and conservation areas are common in the South East, so we check the front-garden rules before quoting.

  • Levels set below the damp-proof course with falls away from the house
  • Break-out of the old surface with waste removal and skip or grab lorry
  • Assessment of the old base: keep, top up or replace
  • New edging, sub-base where needed, and the block drive
  • Drainage added where the old drive sent water to the house or road

What the survey covers

  • Block range, thickness, colour and pattern to suit the house
  • Where rain will go: falls, lawn, border, channel or soakaway
  • Ground conditions under the old surface and how deep the sub-base must be
  • Steps, thresholds and door heights
  • Levels against the damp-proof course (the finished paving must sit at least 150 mm below it)

Rules for front drives in Buckinghamshire

In England, paving in front of the house that covers more than 5 m² needs planning permission unless it is permeable or drains to a lawn, border or soakaway inside your boundary. Permeable block paving, or standard blocks laid to fall onto a planted strip, avoid the need for permission in most cases.

Flats and maisonettes, listed buildings, and homes covered by an Article 4 direction can have tighter rules, and conservation areas, National Parks and National Landscapes restrict some permitted development.

A dropped kerb needs your local highway authority's approval (usually the county, unitary, metropolitan or London borough council), and a new access onto an A, B or C classified road also needs planning permission.

General guidance, not legal advice. Your survey confirms what applies to your home. See the planning guide.

How it works

  1. Send the basics

    Postcode, what you need and a rough size. Photos help.

  2. Survey

    We measure, check levels, ground and drainage, and talk through blocks and patterns.

  3. Written quote

    An itemised quote with the specification, the price and the start date.

  4. The work

    Our paving team builds it to the agreed specification and leaves the site swept.

Replace an old drive in Buckinghamshire: questions

Do I need planning permission for a replacement block drive in Buckinghamshire?

In England, a front drive over 5 m² needs planning permission unless it is permeable or drains to a lawn or border within your boundary. Ask us on the survey if you are unsure.

How much does a replacement block drive cost in Buckinghamshire?

Our guide for Buckinghamshire is £105–£195 per m² including VAT, so a 45 m² replacement drive is usually about £4,600–£8,750. Your fixed price follows the survey.

How long does a replacement block drive take to build?

Most homes take between three and seven working days, depending on size, the dig and the drainage. Your quote gives the expected duration.

Do you cover Milton Keynes, High Wycombe and Aylesbury?

Yes. We cover all of Buckinghamshire, including Milton Keynes, High Wycombe and Aylesbury.

Neighbouring areas

Next step

Get a guide price in two minutes

Answer four quick questions for an instant guide price, then book a free survey to fix it in writing. Repairs and cleaning can often be priced from photos.

Hands laying charcoal paving blocks in herringbone on a sand bed
CallGet a quote